;  ESLMASTR.GEN  TurboDOS v1.41+C.00      16jul87
;
CNFTBL		; Configuration table
STDMASTR       ; Modules for a network master system
BNKMGR         ; Memory Bank Manager
BNK1270        ; Memory Bank Driver for Model 1270 board
CPMSUP         ; CP/M Function Support
;MPMSUP         ; MP/M Function Support		/* set for full CP/M support
;QUEMGR         ; MP/M queuing function support /* set for full CP/M supp.
NITIMS         ; Cold-start initialization, particularly hardware init
MPENIT         ; Memory parity/page 0 initialization
RTCIMS         ; Real-time-clock driver
;SUBMIT         ; To emulate CP/M processing of $$$.SUB /* set for full CP/M 
PATCH          ; Software 2000 Patch Area
;
;==============================================================================
;  SERIAL I/O CONTROLLERS
;    If you don't have any Model 630 or Model 480 I/O boards, choose SET ONE.
;  With SET ONE, you can choose either CONREM and 2 printers, or CONSOL and
;  1 printer.
;    If you have one or more I/O boards, choose SET TWO.  With SET TWO, you
;  can choose as many devices as you have serial ports.
;==============================================================================
;  Set One
;
ZS1270          ; Fast serial I/O driver for Model 1270 ONLY
;
;  Set Two
;
;ZSSER          ; Serial I/O handler: must be present
;ZSSCC          ; Serial driver for Model 1270 ports
;ZSACE          ; Serial driver for Model 631 and 480 boards - "Asynchronous
;              ; Communications Elements"
;==============================================================================
;  CONSOLE SELECTION - Choose one
;==============================================================================
CONREM         ; Console emulator for use by MASTER program run from slave
;CONSOL         ; Choose this module if you have a terminal on the master
;
;==============================================================================
;  PRINTER SELECTION
;  How many printers you can choose depends upon how many serial ports you
;  have available.  Which drivers you choose depends upon your printers.
;  In any case, remember that TURBOGEN only recognizes CTS, XON, and ETX,
;  serial drivers, in that order.  DO NOT CHANGE THE ORDER OF THE DRIVERS.
;==============================================================================
;LST300         ; No-handshake Serial Printer at 300 baud
;LSTXON		; XON/XOFF printer
LSTCTX         ; CTS printer with optional programmed delay
;LSTETX         ; ETX-ACK Serial Printer
;LSTIMS         ; Centronics Parallel Printer
;LSTNEC         ; NEC or Diablo Parallel Printer
;
;==============================================================================
;  NETWORKS
;==============================================================================
;  If you have:					then choose:
;
;  A.  Model 740, 862, or 1081 slaves ONLY	The 1 module in SET ONE
;  B.  Model 1270 slaves ONLY			All 5 modules in SET TWO
;  C.  Both 1270 and any of 740, 862, or 1081	Both SET ONE and SET TWO
;
;* SET ONE:  This module services the Model 740, 862, and 1081 slaves
;
MCD740         ; Master Circuit Driver for Circuit 0
;
;* SET TWO:  These modules service the Model 1270 slaves
;
;MCD            ; Master Circuit Driver for Circuit 1
;CKTDCB         ; Circuit Device Control Blocks
;CKT12X         ; Slave Suffix Table & Type - patch points
;SPB127         ; Slave Intermediate Loader for Model 1270
;SPB124         ; Slave Intermediate Loader for Model 1240
;RESSLV         ; Routine to reset slave & download intermediate loader
;
;==============================================================================
;  DISKS
;
;  The modules we supply allow you to choose one of 5 configurations:
;
;  A.	Floppies only.
;  B.	Floppies and the non-DMA winchesters (C00821 controller).
;  C.	Floppies and the DMA winchesters (C01100 controller).
;  D.	Floppies and cartridge configured as 12 8-megabyte logical disks.
;  E.	Floppies and cartridge configured as 6 16-megabyte logical disks.
;
;  Choose one of the sets below accordingly.
;
;  NOTE:	"ZSUB", "ZZIPUSH", and "ZLUT" must be selected regardless.
;
;  NOTE:	The order of the driver modules determines the name of the
;		driver entry point.  For example, if you have Floppies and
;		a Winchester, the Floppy Driver (for both 8" and 5") will
;		be DSKDRA, and the Winchester Driver will be DSKDRB.  If you
;		have Floppies and a Cartridge, the Floppy Driver will be
;		DSKDRA, and the Cartridge Driver will be DSKDRB.  You need
;		to know this in order to fill "DSKAST" in STDMASTR.PAR.
;==============================================================================
;
;  Routines needed regardless of configuration
;
ZSUB           ; Common I/O subroutines
ZZIPUSH        ; Register save/restore routines for Interrupt Service
ZLUT           ; Logical Unit Table
;
;  A.  Floppies only.
;
;FD930          ; Modules needed to run a Model 930 Floppy controller
;               ; on a system without a Winchester
;
;  B.  Floppies and non-DMA winchester
;
;WD821P          ; Modules needed to run floppies and
;               ; a Model C00821 controller (non-DMA)
;
;  C.  Floppies and DMA winchester
;
WD1100P       ; Modules needed to run floppies and
;              ; a Model C01100 controller (DMA)
;
;  D.  Floppies and cartridge, as 6 16-megabyte logical drives
;
;FD930          ; Model 930 Floppy controller
;CD6-16         ; Up to 6 16 Megabyte logical drives
;
;  E.  Floppies and cartridge, as 12 8-megabyte logical drives
;
;FD930          ; Model 930 Floppy controller
;CD12-8         ; Up to 12 8 Megabyte logical drives
;
;
;==============================================================================
;  USER-WRITTEN DRIVERS
;  If you have any, add them here.
;==============================================================================
