Siemens MX300 ?-Taste Drücken, es wird ein dump erstellt und mit befindet man sich im Monitorprogramm. List of available Help pages sy? Symbols used in commands TS? Teleservice commands SI? SINIX commands for boot- and kernel-location u? Utilities page t? Test commands and tools page io? IO system commands -------------------------------------------------------------------------- Symbols [sy?] @ = address in hex # = number contextdependent ~ = condition- & command-dependent s.t? L = length in bytes C = hex-character (...) = (unit,offset in [s]#)(memory-@,length-#) s# offset in sectors ,# offset in K-Bytes unitnumber layout: 0000 = 4 digit hex number (leading zeros are redundant) ||||> partition: addressable parts on 1 unit (like floppy and disk) |||> unit: physical unit (like floppy drive, disk drive, LUN || with SCSI) connected to a device ||> device: SCSI ID (up to 7 units may be connected to 1 SCSI ID) |> controller: currently not used. *C is doing the job. ATTENTION! The unit number is now interpreted as a hex number! (f.e. FL0 is now 20 not 32 anymore). -------------------------------------------------------------------------- Teleservice [TS?] TS? this help TSe [d] TS enable [with default param, set WFC] TSd [d] TS disable [clear WFC] TSl TS interfacelines states (break with DEL) TSp[?] [i1 i2 i3] TS parameters [info,help] [ind1 ind2 ind3] TShs[?] [string] TS handshake signals [info,help] [param] TSf[?] [string] TS condition flags [info,help] [param] res[e,d] Reset with BREAK [enable,disable] -------------------------------------------------------------------------- SINIX commands [SI?] bootloc string define Systemboot location bootdr drivetype define Systemboot drive bootloc? print the defined location and the location the firmware booted from sinixloc string define the kernel location sinixloc? print the defined kernel location SI? this help If string contains more than 1 command, enclose string in "" valid drivetypes: 0: 5 1/4" DD-Floppy, Omti 1: 5 1/4" DD-Floppy 2: 5 1/4" SD/DD-Floppy 3: 3 1/2" ND-Floppy 4: 5 1/4" HD-Floppy 5: 3 1/2" HD-Floppy 6: Harddisk (ESDI) 6: Harddisk (ST506) 8: Streamer (QIC) 9: SCSI Floppy 10: SCSI Harddisk 11: SCSI Streamer 12: SCSI CD-ROM 13: invalid Systemboot location:%s Drive: %s Systemboot booted from: %s Drive: %s SINIX location: -------------------------------------------------------------------------- Utilities [u?] passwd change the firmware password [l,,r,w](...)[(...)] load, load-start, read, write dsk,fl,str D(...) Display dataoffset in x.out-file ; cat commands return(1) K?[#] display[startnumber] K# start command with index # ai display icu registers ci # [0,1] # change icu reg index [addr] value in[e,d] interrupts [enable,disable] cm[b,w,d] @ # change memory [byte,word,double] addr data D [@,K#] [#] display string [addr,comm] [stringcount] d @ L display memory d[b,w,d]~ @ L display memory, endless. LOOP must be set f[b,w,d]~ @ @ C fill memory. With LOOP set, endless. s[=,s,m][,,b,w,d] @ @ L string[~comp,seek,move][byte,word,double] smb [K#,@] [K#,@] L string move with command strings P printer on/off kb[g,i] keyboard at 97801 [german,international] dt @ transfer data in 'intel hex' format to address via DUART chan 1. Parameters see iop? ph[s,c,?] powerhold FF [set,clear,test] x[,?] [#] [set,show] cond. switch (0: reset, else: |=) 0x0100 no status print ^ position to line 24 on screen mbra # # set the multibus window mb? [@ @] mb window/mapper info [mbstart mbend] mbm [@ @ [@ [#]]] mb map set. mbstart mbend [phys_start [inval]] mb[e,d] mb map [enable,disable] reset do reset pof poweroff scsidevices generate list of connected scsi bus devices scsibusreset reset on the scsi bus, scsi driver reinit -------------------------------------------------------------------------- Test tools [t?] tr1 @ @ # mem-probe start end step (switch caches off!) tr2[b,w,d] @ L # ~memory test, write all, read all tr3[b,w,d] @ L # ~memory test, test address for address tr4 @ # RAS/CAS relations bankaddr cycles tcpulock Testing locked cpu-memory rmw cycles (special) ter2 @ L # edc ram test, write all read all ter3 @ L # edc ram test, test address for address tma[3] # ~test the mapper memory, [similar to t3] mb[m,?] [@ @ [@ [#]]] mb map set. mbstart mbend [phys_start [valid]] tcl testing ram, registers and run of the clock tic testing the icu x[,?] [#] [set,show] cond. switch (0: reset, else: |=) 0x1 Trigger 0x4 LOCK 0x10 MMU_ST 0x2 iolock 0x8 LOOP 0x100 no status print tethprom D566: test the ethernet prom tlan # D566: test the lan chip i82596 0 controller selftest 1 0 + initialize test 2 1 + register dump test 3 2 + TimeDomain Reflectometer (TDR) test tscsi D566: test the scsi controller chip 53C710 -------------------------------------------------------------------------- IO system commands [io] io? this help ioe # io enable desc iod # io disable desc iop[?] # [i1 i2 i3] io parameters [info,help] desc [ind1 ind2 ind3] iohs[?] # [string] io handshake signals [info,help] desc [param] iol # io lines desc (break with DEL) valid descriptors: 0: Console 2: Printer